GE DRYER · SAN BRUNO
GE dryer not heating in San Bruno? We fix it.
A GE dryer that tumbles fine but dries a load cold is one of the most common laundry calls we run. The drum motor and the heat circuit are separate, so when the heat quits the dryer still spins. It is almost always one part on the heat side, and worth fixing.
We handle GE dryer not heating repairs across San Bruno, from Mills Park, Crestmoor, Rollingwood to the surrounding neighborhoods.
We cover San Bruno with our San Mateo County technician (Mid-Peninsula). Here is the short version; the full guide is on the GE Dryer Not Heating page.
- $99 diagnostic (credited toward the repair)
- Same or next-day best effort
- CSLB #1136642
Why this happens
What we look for first.
- Blown thermal fuse (electric and gas). GE dryers carry a one-shot thermal fuse on the blower housing or heat duct. When the dryer overheats the fuse opens and kills the heat circuit for good. The drum keeps turning, so people think the heater died when really the safety tripped. We meter the fuse for continuity. If the vent run is choked, we say so and point you to a vent service; that is not our trade, and a new fuse can blow again.
- Burned-out heating element (electric models). On GE electric dryers the element is a nichrome coil inside a sheet-metal can at the back of the cabinet. The coil sags with age and either breaks open or grounds against the housing. A broken coil reads open on the meter and gives you a stone-cold load. A grounded coil can heat constantly or trip the breaker. We pull the element, ohm it terminal to terminal, check for a short to ground, and swap the assembly if it is bad.
Full causes and diagnostic steps: GE Dryer Not Heating.
Serving San Bruno
San Bruno: response and coverage.
San Bruno sits close to our San Mateo base and is regular territory for us near SFO. No same-day guarantee, but the short distance means it schedules easily most weeks.
Neighborhoods we cover regularly in San Bruno: Mills Park, Crestmoor, Rollingwood. Beyond those, our service area in San Bruno covers the city limits.
San Bruno is one ZIP, 94066, tract homes from the 1940s through the 1960s climbing the hills in Rollingwood, Crestmoor, and Portola Highlands, most on original or first-replacement kitchens. Everyday brands: GE, Whirlpool, Samsung, LG, and Maytag.
Pricing and warranty
What it costs. What we stand behind.
-
$99
Diagnostic visit. Credited toward the repair.
-
Typical
Repair pricing is provided in a written estimate after the $99 on-site diagnosis, which is credited toward the repair.
-
Warranty
You get a parts and labor warranty in writing before we start: from 3 months to 2 years depending on the type of repair. Standard repairs carry 3 months on parts and labor, inverter boards 1 year, and a full sealed-system rebuild 2 years. We put the part, the price, and the labor on the quote before we touch the machine, so you know exactly what is covered.
Before you call
Is your washer or dryer worth repairing?
Repair price depends on the fault and access, especially on stacked units. If the machine cost under $1,000 new, the repair math may not work. We diagnose the machine on site and provide the written repair estimate before any work starts.
Under $1,000 new, repair may not be the right investment. Premium, stacked, and commercial-grade machines are stronger repair candidates, and we will give you a straight recommendation after diagnosis.
Worth checking yourself first: clear the lint trap and the vent path, make sure the load is not overloaded or sitting unbalanced, and look for a kink or clog in the drain hose. If the machine truly is done, put that money toward the replacement. And since we also run an HVAC side of the business, a free assessment visit comes with any furnace, A/C, or heat pump replacement.
Related
More on GE and San Bruno.
Nearby cities
GE dryer not heating near San Bruno.
Also in San Bruno
Other dryer repairs we do in San Bruno.
Ready to book the San Bruno call?