How quickly can you reach Woodside for a DCS service call?

Drive time from San Ramon is about 50 to 60 minutes via I-680 south and CA-92 or I-280. We route Woodside on the same Peninsula day as Hillsborough and Portola Valley, and same or next-day work is realistic once we've got you a window, written arrival time included.

Do you stock DCS parts, or order them as needed?

Spark electrodes, reignition modules, burner switches, glow-bar igniters, and both NG and LP orifices stay on the truck, since a lot of Woodside runs on propane. Transformers, dual thermal valves, and convection motors I bring in for the specific job. Fisher & Paykel owns DCS now, and parts flow through their supply chain.

What is the typical cost for a DCS ignition or oven igniter call in Woodside?

The diagnostic runs $99 and gets credited toward the repair. We provide a written repair estimate after the on-site diagnosis and before any work starts. Gas work goes out under CSLB #1136642, with a written quote before anything starts.

DCS · WOODSIDE

Service · All DCS Models

DCS Cooking Appliance Repair · Woodside, CA

DCS by Fisher & Paykel RGS pro all-gas range, integrated grill and griddle modules, and built-in outdoor grill service for Woodside.

$99 diagnostic (credited toward the repair)
Same or next-day best effort
CSLB #1136642

Call (925) 999-4095

DCS in Woodside

DCS in Woodside kitchens.

Woodside's larger properties along Mountain Home Road and Kings Mountain Road tend to build out an outdoor kitchen near the pool or the horse barn, and DCS built-in grills show up there more than in the main house. Indoors, the RGS series range with a GL grill or GD griddle module sits in the estate kitchen alongside the rest of the panel-ready lineup.

Most of what we pull on these installs is top-burner ignition and simmer trouble once a range clears ten years, and out here that's compounded by properties that run on propane rather than natural gas, since a conversion done years ago sometimes left the wrong orifices in place. Drive time out of San Ramon runs 50 to 60 minutes on I-680 south into CA-92 or I-280.

Common repairs we do

What we close on the truck.

Ignition clicks but the burner won't catch. No spark, or a click with nothing behind it. I trace it to the spark electrode, the reignition module, the transformer, or the burner switch, whichever tests out of range.
Burner won't hold a simmer, or flame runs yellow. Usually restricted jets, a locating pin not seated, or leftover orifices from a propane conversion done on the property years back. I clean the jets, reseat the pins, and reorifice to 10 inch WC LP where needed.
Grill or griddle module barely lighting. A weak igniter or a stuck thermal valve on the GL or GD module, more exposed to weather on an outdoor kitchen setup than an indoor range sees. I replace whichever one tests bad.
Glow-bar igniter not pulling enough current. It glows but can't draw enough amperage to open the safety valve. I swap the glow-bar, or the dual thermal valve and convection motor if that turns out to be the real cause.

Models we service

DCS product lines.

RGS professional gas ranges (30, 36, 48, 60 inch)
Sealed dual-orifice burners
Integrated grill and griddle modules
Infrared broiler and gas convection oven
Built-in outdoor grills

Pricing and warranty

What it costs. What we stand behind.

$99

Diagnostic visit. Credited toward the repair.
Written

3 months standard, 1 year on inverter boards, up to 2 years on sealed-system rebuilds. Quoted in writing before work starts.
CSLB

#1136642. Bonded and insured. We file warranty paperwork when applicable.

Nearby cities

DCS service in neighboring cities.

More cities

DCS across our service area.

FAQ

DCS in Woodside questions, answered.

How quickly can you reach Woodside for a DCS service call?

Drive time from San Ramon is about 50 to 60 minutes via I-680 south and CA-92 or I-280. We route Woodside on the same Peninsula day as Hillsborough and Portola Valley, and same or next-day work is realistic once we've got you a window, written arrival time included.
Do you stock DCS parts, or order them as needed?

Spark electrodes, reignition modules, burner switches, glow-bar igniters, and both NG and LP orifices stay on the truck, since a lot of Woodside runs on propane. Transformers, dual thermal valves, and convection motors I bring in for the specific job. Fisher & Paykel owns DCS now, and parts flow through their supply chain.
What is the typical cost for a DCS ignition or oven igniter call in Woodside?

The diagnostic runs $99 and gets credited toward the repair. We provide a written repair estimate after the on-site diagnosis and before any work starts. Gas work goes out under CSLB #1136642, with a written quote before anything starts.

Need DCS service in Woodside?

Tell us what is broken. We will quote it.